Op deze website gebruiken we cookies om content en advertenties te personaliseren, om functies voor social media te bieden en om ons websiteverkeer te analyseren. Ook delen we informatie over uw gebruik van onze site met onze partners voor social media, adverteren en analyse. Deze partners kunnen deze gegevens combineren met andere informatie die u aan ze heeft verstrekt of die ze hebben verzameld op basis van uw gebruik van hun services. Meer informatie.

Akkoord

Vraag & Antwoord

Anders (hardware)

SMART

Captain_Kansloos
2 antwoorden
  • Kan iemand mij vertellen wat het verschil is bij SMART tussen 'value is normal' en 'always passing' in Aida32. Ik heb twee schijven, en vraag me af of ze 100% in orde zijn. Hier de gegevens uit Aida32:

    [ WDC WD360GD-00FNA0 (WD-WMAH91245310) ]

    01 Raw Read Error Rate 51 200 191 0 OK: Value is normal
    03 Spin Up Time 21 85 81 2258 OK: Value is normal
    04 Start/Stop Count 40 100 100 69 OK: Value is normal
    05 Reallocated Sector Count 140 200 200 0 OK: Value is normal
    07 Seek Error Rate 51 200 200 0 OK: Value is normal
    09 Power-On Time Count 0 99 99 1093 OK: Always passing
    0A Spin Retry Count 51 100 253 0 OK: Value is normal
    0B Calibration Retry Count 51 100 253 0 OK: Value is normal
    0C Power Cycle Count 0 100 100 68 OK: Always passing
    C2 Temperature 0 114 253 29 OK: Always passing
    C4 Reallocation Event Count 0 200 200 0 OK: Always passing
    C5 Current Pending Sector Count 0 200 200 0 OK: Always passing
    C6 Off-Line Uncorrectable Sector Count 0 200 200 0 OK: Always passing
    C7 Ultra ATA CRC Error Rate 0 200 253 0 OK: Always passing
    C8 Write Error Rate 51 200 125 0 OK: Value is normal

    [ Maxtor 6Y080L0 (Y2635DFE) ]

    03 Spin Up Time 63 224 224 11246 OK: Value is normal
    04 Start/Stop Count 0 253 253 94 OK: Always passing
    05 Reallocated Sector Count 63 253 253 0 OK: Value is normal
    06 Read Channel Margin 100 253 253 0 OK: Value is normal
    07 Seek Error Rate 0 253 252 0 OK: Always passing
    08 Seek Time Performance 187 253 249 54527 OK: Value is normal
    09 Power-On Time Count 0 250 250 7339 OK: Always passing
    0A Spin Retry Count 157 253 252 0 OK: Value is normal
    0B Calibration Retry Count 223 253 252 0 OK: Value is normal
    0C Power Cycle Count 0 253 253 102 OK: Always passing
    C0 Power-Off Retract Count 0 253 253 0 OK: Always passing
    C1 Load/Unload Cycle Count 0 253 253 0 OK: Always passing
    C2 Temperature 0 253 253 24 OK: Always passing
    C3 Hardware ECC Recovered 0 253 252 1264 OK: Always passing
    C4 Reallocation Event Count 0 253 253 0 OK: Always passing
    C5 Current Pending Sector Count 0 253 253 0 OK: Always passing
    C6 Off-Line Uncorrectable Sector Count 0 253 253 0 OK: Always passing
    C7 Ultra ATA CRC Error Rate 0 199 199 0 OK: Always passing
    C8 Write Error Rate 0 253 252 0 OK: Always passing
    C9 <vendor-specific> 0 253 252 79 OK: Always passing
    CA <vendor-specific> 0 253 252 0 OK: Always passing
    CB <vendor-specific> 180 253 252 9 OK: Value is normal
    CC <vendor-specific> 0 253 252 0 OK: Always passing
    CD <vendor-specific> 0 253 252 0 OK: Always passing
    CF <vendor-specific> 0 253 252 0 OK: Always passing
    D0 <vendor-specific> 0 253 252 0 OK: Always passing
    D1 <vendor-specific> 0 190 190 0 OK: Always passing
    63 <vendor-specific> 0 253 253 0 OK: Always passing
    64 <vendor-specific> 0 253 253 0 OK: Always passing
    65 <vendor-specific> 0 253 253 0 OK: Always passing
  • [quote:5c620f2ba0="MeM"]Kan iemand mij vertellen wat het verschil is bij SMART tussen 'value is normal' en 'always passing' in Aida32. Ik heb twee schijven, en vraag me af of ze 100% in orde zijn. Hier de gegevens uit Aida32:

    [ WDC WD360GD-00FNA0 (WD-WMAH91245310) ]

    01 Raw Read Error Rate 51 200 191 0 OK: Value is normal
    03 Spin Up Time 21 85 81 2258 OK: Value is normal
    04 Start/Stop Count 40 100 100 69 OK: Value is normal
    05 Reallocated Sector Count 140 200 200 0 OK: Value is normal
    07 Seek Error Rate 51 200 200 0 OK: Value is normal
    09 Power-On Time Count 0 99 99 1093 OK: Always passing
    0A Spin Retry Count 51 100 253 0 OK: Value is normal
    0B Calibration Retry Count 51 100 253 0 OK: Value is normal
    0C Power Cycle Count 0 100 100 68 OK: Always passing
    C2 Temperature 0 114 253 29 OK: Always passing
    C4 Reallocation Event Count 0 200 200 0 OK: Always passing
    C5 Current Pending Sector Count 0 200 200 0 OK: Always passing
    C6 Off-Line Uncorrectable Sector Count 0 200 200 0 OK: Always passing
    C7 Ultra ATA CRC Error Rate 0 200 253 0 OK: Always passing
    C8 Write Error Rate 51 200 125 0 OK: Value is normal

    [ Maxtor 6Y080L0 (Y2635DFE) ]

    03 Spin Up Time 63 224 224 11246 OK: Value is normal
    04 Start/Stop Count 0 253 253 94 OK: Always passing
    05 Reallocated Sector Count 63 253 253 0 OK: Value is normal
    06 Read Channel Margin 100 253 253 0 OK: Value is normal
    07 Seek Error Rate 0 253 252 0 OK: Always passing
    08 Seek Time Performance 187 253 249 54527 OK: Value is normal
    09 Power-On Time Count 0 250 250 7339 OK: Always passing
    0A Spin Retry Count 157 253 252 0 OK: Value is normal
    0B Calibration Retry Count 223 253 252 0 OK: Value is normal
    0C Power Cycle Count 0 253 253 102 OK: Always passing
    C0 Power-Off Retract Count 0 253 253 0 OK: Always passing
    C1 Load/Unload Cycle Count 0 253 253 0 OK: Always passing
    C2 Temperature 0 253 253 24 OK: Always passing
    C3 Hardware ECC Recovered 0 253 252 1264 OK: Always passing
    C4 Reallocation Event Count 0 253 253 0 OK: Always passing
    C5 Current Pending Sector Count 0 253 253 0 OK: Always passing
    C6 Off-Line Uncorrectable Sector Count 0 253 253 0 OK: Always passing
    C7 Ultra ATA CRC Error Rate 0 199 199 0 OK: Always passing
    C8 Write Error Rate 0 253 252 0 OK: Always passing
    C9 <vendor-specific> 0 253 252 79 OK: Always passing
    CA <vendor-specific> 0 253 252 0 OK: Always passing
    CB <vendor-specific> 180 253 252 9 OK: Value is normal
    CC <vendor-specific> 0 253 252 0 OK: Always passing
    CD <vendor-specific> 0 253 252 0 OK: Always passing
    CF <vendor-specific> 0 253 252 0 OK: Always passing
    D0 <vendor-specific> 0 253 252 0 OK: Always passing
    D1 <vendor-specific> 0 190 190 0 OK: Always passing
    63 <vendor-specific> 0 253 253 0 OK: Always passing
    64 <vendor-specific> 0 253 253 0 OK: Always passing
    65 <vendor-specific> 0 253 253 0 OK: Always passing[/quote:5c620f2ba0]

    als er met je harde schijf wat is dan merk je dat aan bad sectors en begint S.M.A.R.T vanzelf te waarschuwen dat er iets niet goed is.
    ik zal me er maar niet druk om maken wat aida32 zegt

Beantwoord deze vraag

Dit is een gearchiveerde pagina. Antwoorden is niet meer mogelijk.