Vraag & Antwoord
[SUSE 8.0] Set up grafische interface met SaX2
7 antwoorden
- [quote:4224bf8329="Butch"] Volgens de On Screen Display van mijn scherm is de frequentie 60kHz/75Hz. Waar zou ik dat in XF86Config aan moeten passen? [/quote:4224bf8329] Je zou om te beginnen in Section "Screen"
[code:1:4224bf8329]
EndSubSection
SubSection "Display"
Depth 16
Modes "1280x1024" "1024x768" "1024x768" "832x624" "800x600" "800x600" "640x480" "640x480" "720x400"
EndSubSection [/code:1:4224bf8329] die "1280x1024" kunnen verwijderen. Uiteraard maak je van tevoren een reserve kopie van die XF86Config voor het geval het fout gaat. En uiteraard controleer je de HorizSync en VertRefresh uit de Section "Monitor" met je met de gegevens van je monitor handleiding - Tijdens installatie van Linux met Yast2 heb ik ervoor gekozen om geen grafische interface te installeren. Nu wil ik dit alsnog doen. Volgens de Handige Handleiding moet dit met Sax2. Als ik dit programma start (als root uiteraard) gaat het (TFT)scherm na enkele ogenblikken op zwart en verschijnt de melding: [i:48bf1650cc]Invalid mode (80kHz, 75 Hz)[/i:48bf1650cc] en lijkt het programma te hangen.
Nu maak ik gebruik van een KVM-switch en ik weet dat die wel eens voor wat 'ruis' zorgt , dus het programma nogmaals gedraaid maar nu zonder KVM-switch. Nu komt het programma wel tot een einde maar produceert de volgende logfile. Het systeem bevat een Matrox Millenium II kaart. Heeft iemand suggesties?
[code:1:48bf1650cc]===========================================================
SaX2 log: SaX2 version 4.3 - CVS Release: 1.30 2002/02/28
———————————————————–
SaX2 CVS build number: 16066
————————
SaX2 caller parameter:
————————
no parameter(s) given
————————
SaX2 framebuffer info:
————————
mode "1024x768-76"
# D: 78.653 MHz, H: 59.949 kHz, V: 75.694 Hz
geometry 1024 768 1024 768 16
timings 12714 128 32 16 4 128 4
rgba 5/11,6/5,5/0,0/0
endmode
Frame buffer device information:
Name : VESA VGA
Address : 0xde000000
Size : 4194304
Type : PACKED PIXELS
Visual : TRUECOLOR
XPanStep : 0
YPanStep : 0
YWrapStep : 0
LineLength : 2048
Accelerator : No
———————————————————–
SaX2 compiled for: [SuSE Linux 8.0 (i386)]
———————————————————–
—————————–
Sysp: Mouse detection data…
—————————–
Mouse0 => Protocol : ps/2
Mouse0 => Device : /dev/mouse
Mouse0 => Buttons : -1
Mouse0 => Wheel : 0
Mouse0 => Emulate : 1
—————————–
Sysp: Keyboard detection data…
—————————–
Keyboard0 => XkbLayout : us
Keyboard0 => XkbModel : pc101
Keyboard0 => Protocol : Standard
Keyboard0 => MapName : Generic keyboard [ pc101 ]
—————————–
Sysp: Server detection data…
—————————–
Card0 => BusId : 0x1
Card0 => SlotId : 0x00
Card0 => FuncId : 0x0
Card0 => Vendor : Matrox
Card0 => Device : MGA 2164W AGP
Card0 => VID : 0x102b
Card0 => DID : 0x051f
Card0 => Module : mga
Card0 => BusType : AGP
Card0 => Detected : 1
Card0 => Flag : DEFAULT
Card0 => SUB-VID : 0x102b
Card0 => SUB-DID : 0x2100
—————————–
Sysp: XStuff detection data…
—————————–
Card0 => DDC : LTN020E
Card0 => Primary : 01-00-0
Card0 => Chipset : mga2164w AGP
Card0 => Vsync : 75
Card0 => Hsync : 60
Card0 => Vesa : 720 400 28 70
Card0 => Vesa : 720 400 35 88
Card0 => Vesa : 640 480 28 60
Card0 => Vesa : 640 480 32 67
Card0 => Vesa : 640 480 34 72
Card0 => Vesa : 640 480 36 75
Card0 => Vesa : 800 600 36 60
Card0 => Vesa : 800 600 45 75
Card0 => Vesa : 832 624 46 75
Card0 => Vesa : 1024 768 60 87
Card0 => Vesa : 1024 768 53 70
Card0 => Vesa : 1024 768 57 75
Card0 => Vesa : 1280 1024 60 75
Card0 => Vesa : 640 480 36 75
Card0 => Vesa : 800 600 45 75
Card0 => Dacspeed : 250
Card0 => Memory : 4096
Card0 => Current : 01-00-0
Card0 => RawDef : None
Card0 => Option : NoHal
Card0 => Extension : None
Card0 => Module : mga
Card0 => Display : CRT
Card0 => Size : 30x23
—————————–
Sysp: 3D detection data…
—————————–
Card3D0 => Install : <none>
Card3D0 => Remove : <none>
Card3D0 => Script : switch2mesasoft
Card3D0 => Packages : mesasoft
—————————————-
xc: Auto configuration for startup…
—————————————-
Section "Files"
FontPath "/usr/X11R6/lib/X11/fonts/misc:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/local"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/Type1"
FontPath "/usr/X11R6/lib/X11/fonts/URW"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo"
FontPath "/usr/X11R6/lib/X11/fonts/PEX"
FontPath "/usr/X11R6/lib/X11/fonts/cyrillic:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/latin2/misc:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/latin2/75dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/latin2/100dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/latin2/Type1"
FontPath "/usr/X11R6/lib/X11/fonts/latin7/75dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/baekmuk:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/japanese:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/kwintv:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/truetype"
FontPath "/usr/X11R6/lib/X11/fonts/uni:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/CID"
FontPath "/usr/X11R6/lib/X11/fonts/ucs/misc:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/ucs/75dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/ucs/100dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/hellas/misc:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/hellas/75dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/hellas/100dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/hellas/Type1"
FontPath "/usr/X11R6/lib/X11/fonts/misc/sgi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/xtest"
ModulePath "/usr/X11R6/lib/modules"
RgbPath "/usr/X11R6/lib/X11/rgb"
EndSection
Section "Module"
Load "dbe"
Load "type1"
Load "speedo"
Load "freetype"
Load "extmod"
EndSection
Section "ServerFlags"
Option "AllowMouseOpenFail"
EndSection
Section "InputDevice"
Driver "Keyboard"
Identifier "Keyboard[0]"
Option "MapName" "Generic keyboard [ pc101 ]"
Option "Protocol" "Standard"
Option "XkbLayout" "us"
Option "XkbModel" "pc101"
Option "XkbRules" "xfree86"
EndSection
Section "InputDevice"
Driver "mouse"
Identifier "Mouse[1]"
Option "Device" "/dev/mouse"
Option "Emulate3Buttons" "on"
Option "Name" "Autodetection"
Option "Protocol" "ps/2"
Option "Vendor" "Sysp"
EndSection
Section "Monitor"
DisplaySize 300 230
HorizSync 31-80
Identifier "Monitor[0]"
ModelName "1280X1024@75HZ"
Option "DPMS"
VendorName "–> VESA"
VertRefresh 50-75
UseModes "Modes[0]"
EndSection
Section "Modes"
Identifier "Modes[0]"
Modeline "1280x1024" 127.80 1280 1296 1552 1736 1024 1024 1035 1070
Modeline "1280x1024" 135.0 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync
Modeline "1024x768" 76.49 1024 1040 1216 1400 768 768 776 802
Modeline "832x624" 50.54 832 848 968 1112 624 624 631 652
Modeline "800x600" 46.80 800 816 928 1072 600 600 606 626
Modeline "640x480" 29.95 640 656 720 864 480 480 485 501
Modeline "720x400" 28.08 720 736 824 1008 400 400 404 417
EndSection
Section "Device"
BoardName "MGA 2164W AGP"
BusID "1:0:0"
Driver "mga"
Identifier "Device[0]"
Option "NoHal"
VendorName "Matrox"
EndSection
Section "Screen"
DefaultDepth 16
SubSection "Display"
Depth 15
Modes "1280x1024" "1024x768" "1024x768" "832x624" "800x600" "800x600" "640x480" "640x480" "720x400"
EndSubSection
SubSection "Display"
Depth 16
Modes "1280x1024" "1024x768" "1024x768" "832x624" "800x600" "800x600" "640x480" "640x480" "720x400"
EndSubSection
SubSection "Display"
Depth 24
Modes "1280x1024" "1024x768" "1024x768" "832x624" "800x600" "800x600" "640x480" "640x480" "720x400"
EndSubSection
SubSection "Display"
Depth 32
Modes "1024x768" "1024x768" "832x624" "800x600" "800x600" "640x480" "640x480" "720x400"
EndSubSection
SubSection "Display"
Depth 8
Modes "1280x1024" "1024x768" "1024x768" "832x624" "800x600" "800x600" "640x480" "640x480" "720x400"
EndSubSection
Device "Device[0]"
Identifier "Screen[0]"
Monitor "Monitor[0]"
EndSection
Section "ServerLayout"
Identifier "Layout[all]"
InputDevice "Keyboard[0]" "CoreKeyboard"
InputDevice "Mouse[1]" "CorePointer"
Screen "Screen[0]"
EndSection
Section "DRI"
Group "video"
Mode 0660
EndSection
X connection to :0.0 broken (explicit kill or server shutdown).
X connection to :0.0 broken (explicit kill or server shutdown).
——————————————–
xc: XFree86 log file for AutoConfig…
——————————————–
XFree86 Version 4.2.0 / X Window System
(protocol Version 11, revision 0, vendor release 6600)
Release Date: 23 January 2002
If the server is older than 6-12 months, or if your card is
newer than the above date, look for a newer version before
reporting problems. (See http://www.XFree86.Org/)
Build Operating System: SuSE Linux [ELF] SuSE
Module Loader present
Markers: (–) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/XFree86.0.log", Time: Sun Aug 22 21:12:56 2004
(++) Using config file: "/tmp/sax2-1070/XF86Config"
(EE) MGA(0): Static buffer allocation failed, not initializing the DRI
(EE) MGA(0): Need at least 7680 kB video memory at this resolution, bit depth[/code:1:48bf1650cc]
Bij voorbaat dank
Butch - [quote:2834de8e4c="Butch"]Tijdens installatie van Linux met Yast2 heb ik ervoor gekozen om geen grafische interface te installeren. Nu wil ik dit alsnog doen. Volgens de Handige Handleiding moet dit met Sax2. Als ik dit programma start (als root uiteraard) gaat het (TFT)scherm na enkele ogenblikken op zwart en verschijnt de melding: Invalid mode (80kHz, 75 Hz) en lijkt het programma te hangen. [/quote:2834de8e4c] En op het moment dat je sax2 typt, ben je in tekst mode? En als je nu in tekst mode het probeert met [b:2834de8e4c] yast [/b:2834de8e4c] Hardware > Grafische kaart en monitor. Worden je grafische kaart en monitor dan juist gedetecteerd? Je hebt wel de specificaties van de monitor.
- Op het moment dat ik Sax2 kies ben ik in text mode. Mijn LiteOn LitePanel 150 TFT is middels een KVM-switch aangesloten op een Windows XP box en de bewuste Linux box. De instelling in windows is 1024*768 by 75 Hz en dat is precies wat Yast detecteert.
Als monitor geeft Yast GC150AT/ATA.
Eerlijk gezegd heb ik de indruk dat Yast niets detecteert, maar gewoon laat zien wat hij (of zij?) allang weet. De text mode van Suse 8.0 is immers behoorlijk grafisch…
Butch - [quote:3f85171b5f="Butch"] De instelling in windows is 1024*768 by 75 Hz en dat is precies wat Yast detecteert. [/quote:3f85171b5f]
Maar je in je output [quote:3f85171b5f="Butch"]
[code:1:3f85171b5f] Section "Monitor"
DisplaySize 300 230
HorizSync 31-80
Identifier "Monitor[0]"
ModelName "1280X1024@75HZ"
Option "DPMS"
VendorName "–> VESA"
VertRefresh 50-75
UseModes "Modes[0]"
EndSection [/code:1:3f85171b5f][/quote:3f85171b5f] toont een hogere resolutie. En kloppen die HorizSync en VertRefresh wel? Kun je niet beter proberen de /etc/X11/XF86Config handmatig aan te passen? - Volgens de On Screen Display van mijn scherm is de frequentie 60kHz/75Hz. Waar zou ik dat in XF86Config aan moeten passen?
Butch - Toen ik dit onderwerp startte, had ik de hoop dat mijn probleem eenvoudig op te lossen was. Het is me nu duidelijk dat dat niet zo is. Dus kies ik voor een meer structurele oplossing: ik ga me eerst in het onderwerp verdiepen en als ik er dan nog niet uit kom, zal ik op dit forum (meer gerichte) vragen stellen. Dus bedankt Jolo tot zover! Ik ga eerst mijn huiswerk doen.
Butch
Beantwoord deze vraag
Dit is een gearchiveerde pagina. Antwoorden is niet meer mogelijk.
Gerelateerde vragen
- Voodoo 3 2000 en dri als non-root
- [gentoo] keyboard loop om de x minuten vast
- [Slackware Current] OpenOffice en Fonts
- Slackware resolutie met X
- Ik wil nou toch eindelijk die resolutie eens goed hebben!
- X error tijdens installeren wacom tablet
- [gentoo] twee monitoren en een wacom-bord
- 2 onafhankelijke displays